1726211-2RS1 Bearings
1726211-2RS1 Insert bearing
YET 211-200 Bearings
YET 211-200 Insert bearing

YSP 211-200 SB-2F Bearings

YSP 211-200 SB-2F Bearings
YSP 211-200 SB-2F Bearings

YSP 211-200 SB-2F Insert bearing

Technical Specification of YSP 211-200 SB-2F Bearings


Dimensions of YSP 211-200 SB-2F Bearings

50.8 mm
Bore diameter of sleeve
100 mm
Outside diameter
49.2 mm
Overall bearing width
25 mm
Width of outer ring
69.06 mm
Outside diameter of inner ring
77.6 mm
Outside diameter of locking collar
Distance from locking device side face to raceway centre
Values specified for B1 and s1 are approximate and before the set screw is tightened (sleeve and inner ring bore at starting position).

Caliculation Data of YSP 211-200 SB-2F Bearings

Basic dynamic load ratingC
43.6 kN
Basic static load ratingC0
29 kN
Fatigue load limitPu
1.25 kN
Limiting speed 
3 600 r/min
Calculation factorf0

Mass of YSP 211-200 SB-2F Bearings

1.1 kg


Mounting Information of YSP 211-200 SB-2F Bearings

Set screwG2
Hexagonal key size for set screwN
3.05 mm
Recommended tightening torque for set screw 
7.4 Nm

Product Features of YSP 211-200 SB-2F Bearings

  • Quick and easy mounting
    Different locking methods allow quick and easy mounting of the housing bearing onto the shaft.
  • Adapting to initial misalignment
    Spherical outer surface can be initially misaligned by tilting in the housing
  • Service life
    Long The different sealing solutions available offer a long service life for a variety of applications with high contamination levels.
  • Reduced noise and vibration levels
    Where high noise and vibration levels are required, SKF can provide suitable shaft locking methods.

Applications of YSP 211-200 SB-2F Bearings

Insert bearings (SKF Y-bearings) are based on sealed deep groove ball bearings in the 62 and 63 series, but have a convex outer ring and in most cases an extended inner ring with a specific locking device, enabling quick and easy mounting onto the shaft.The following are examples of applications where insert bearings may be used:

  • Agriculture
  • Food and beverage processing and packaging
  • Air handling
Applications of W 618/0.6 Bearings
Applications of Bearings
Wind Turbines
Applications of Bearings
Steel Industry
Applications of Bearings
Applications of Bearings
Food Processing Machinery
Applications of Bearings
Applications of Bearings
Mining & Construction
Applications of Bearings
Electric motors and generators

FAQ of YSP 211-200 SB-2F Bearings

  • Generally speaking, insert bearings are standard radial bearings that fit into the housing. Although they are usually sold with the housing, these bearings can also be purchased as a stand-alone product to be used as a replacement. While standard radial ball bearings must be pressed into a machined shaft, with special mounting tools, insert bearings can be fitted directly to the shaft with a sliding fit. However, insert bearings are usually mounted on shafts with bores slightly smaller than the bore diameter of the bearing. This loose fit requires a locking device to hold the bearing firmly in place. The inner ring of the bearing extends to one side to accommodate the locking device. In addition, the width of the inner ring of a housing bearing may vary depending on the type of bearing.

Loads are defined by their direction. Loads perpendicular to the shaft are called radial loads and loads parallel to the shaft are called axial (thrust) loads.

DGBB can carry axial loads in both directions, whereas angular contact ball bearings can only carry axial loads in one direction.

More Products

Chat with us
Chat with us
Questions, doubts, issues? We're here to help you!
None of our operators are available at the moment. Please, try again later.
Our operators are busy. Please try again later
Have you got question? Write to us!
This chat session has ended

Request A Quote Today